Saturday, October 29, 2016

Review: JST Transify

Hello and welcome to this week's article!
Today we are going to talk about Jst Transify, the latest version of the transient shaper plugin produced by Joey Sturgis Tones!

Transify is a tool that enables us to control the transient of our sound, and it is used usually for drums, both for single tracks or busses, to decide wether to make it pop more (if the sound is too dull) or less (if it is too snappy and without body).

The interesting thing that differentiates this plugin from the other transient shapers is the amount of controls that it offers: four bands that can be activated and tweaked independently (with the width of each one that can be controlled by a crossover pot), separate attack and sustain controls for each band, to decide in which part of the transient to intervene, a clip switch that adds some limiting and saturation, and an overall input and output control.

Like the other JST plugin, also this one uses graphics that resembles an analog device (scheumorphism), which is very pleasant to see and intuitive, and the plugin is not too demanding in terms of cpu.
I usually was not particularly fond of transient shapers exactly because often they comes with just one band (forcing you either to process the whole track or to do some uncomfortable workaround like splitting a track into 2 or more separate tracks for treating the various eq areas differently), and because they can modify the sound to a point that it doesn't sound much natural anymore.

Transify solves the problem of making the processed track sound too "digital" by adding some console saturation and analog modeling in order to hide better the cold sounding, digital recreation of the transient.

The result is more natural sounding tracks, a control very wide that lets us dial in the right amount of snap in our drum tracks without modifying the eq, and in general a better sounding song, so I really suggest everyone to give this plugin a try.

Features taken from the website:

- Four frequency band ranges available for independent transient processing

- Built-in per-band clip circuit for creating aggressive sounds and preventing peak overages

- Adjust the frequency band ranges for your material using the individual cut-off controls

- Input and Output controls for getting your signal to match levels and optimize gain staging

Become fan of this blog on Facebook! Share it and contact us to collaborate!!

Saturday, October 22, 2016

The difference between tube and solid state amps

Hello and welcome to this week's article!
Today we are going to take a look at the difference between tube watts and solid state, why does everyone say that there is a big difference?
Why does a 100w tube amp overshadows a 100w solid state one in a live environment?
I am no engineer, but we will try today to make a little clarity and to separate the facts from the myth.

Note: this article is an addition to our articles about, speakers and tubes.

Fact: 100w tube = 100w solid state.
The main difference is that a tube amp uses one or more vacuum tubes to amplify the signal while a solid state one relies only on diodes, transistors etc (for the sake of simplicity we won't talk about the many hybrids that uses a solid state power amp adding a tube just to add some harmonic warmth or those who uses digital emulation of tube response).
Then why in a live environment the tube amp usually sounds much more powerful than a solid state amp? For a serie of reasons, which involves the fact that tubes can increase certain harmonics (therefore push a little more the sound on frequences that appear to cut throught the mix better) and the break up limit.

What is the break up threshold?
When playing at a low volume with both a solid state and a tube amp we will notice that the difference between the two amps is not that noticeable, both amps have a certain amount of headroom (the space in which the volume can be increased without causing distortion), but then when we will turn up the volume we will notice that we will reach a level in which the headroom will finish and the amp will start distorting.
It's at this point that a solid state amp will start sounding really bad, therefore the volume excursion ends at the break up limit or a little over, while a tube amp can easily surpass it, since after the breakup the tubes really starts warming up adding a sligh compression and harmonic warmth that actually makes the sound even more pleasant.

What is a workaround that amp manufacturers usually choose to make solid state amps to sound comparable to tube amps? Easy: they add more watts, to let the preamp do his job with no interference.
Examples: the Marshall Mode Four head, which has 350 watt, which is used for example by the Testament guitarist Alex Skolnick, or the Fender Metalhead, which produces 400w, starting from the assumption that usually in order to match a tube amp at full volume a solid state one should usually have the triple of the wattage.

So far we have only talked about guitar amps, but with bass amps the wattages are even more extreme, because it takes even more power to deliver bass frequences with the right clarity, so the same rule applies to bass amplifiers too, and the wattages are even higher.

Myth: tube power amps sounds better than solid state power amps.
This assumption is true as long as you want/need the sound effect of tubes, which is, as we have said, a harmonic enhancement especially in the mid and high frequences and a sligh compression that influences the dynamic range. This is an effect that is often desired in rock, blues and other genres, while many jazz or funk players prefer solid state amps because they sounds usually more "clean", like the Roland Jazz Chorus, which is in production by 40 years and it is still considered an industry standard for the genre. The final word is that you should really try both solutions and find the right one for your music genre, keeping in mind that it's not mandatory to use the power amp type that everyone uses in a certain genre: heavy metal is a genre typically dominated by tube amps, but some of the most influential icons actually have shaped their tone with solid state amps (for example Dimebag Darrell of Pantera or Chuck Schuldiner of Death).

Difference between Peak and Rms wattage: some amps have the wattage calculated in rms (root mean square, which put in simple words is the average volume actually perceived by our ears), and often tube amps have their wattage reported in rms, which means that if they are 100w rms, they can play at 100w for hours, while other amps (often solid state ones) have their wattage expresses in peak: this means that if an amp is 100w peak, it can sound 100w for one fraction of a second, for example, while for most of the time it will play at around 50w rms. This is more of a marketing gimmick, and we should really be careful when reading the specifics of two amps when comparing them, or when choosing which one to buy.
This is another of the most common reasons why tube amps usually seems to sound much louder than solid state ones: the wattage is reported in a different way.

Become fan of this blog on Facebook! Share it and contact us to collaborate!!

Saturday, October 15, 2016

The most famous song structures in modern music

Hello and welcome to this week's article!
Today we are presenting a new blog category: songwriting!
With these articles we are going to break down some of the creation processes behind the most successful songs in terms of chords, sound choices, structures and arrangements.

Let's start by saying that by no mean these article wants to become a guideline on how you should write a song: a song is an art composition, and the main content it should convoy is INSPIRATION, not following guidelines.
If you don't have a musical or lyrical message to deliver, it's totally useless to apply the most effective structure, the most common chord progressions and the most modern sounds: music is not marketing, and the "fake" products, those created just with the cookie-cutter are easy to spot and will never remain in the heart of the listener.

Let's focus on the most common song structure: a rock or a pop song is often composed by 5 parts:

A) intro: the introduction of the song
B) verse: the part in which the bulk of the lyrics are
C) bridge: the part used as a connection between the verse and the chorus
D) chorus: the fulcrum of the song
E) instrumental: a part of the song without lyrics, e.g. a guitar solo

By listening to your favourite pop/rock/metal songs you'll notice that statistically, the most common structure is A-B-C-D-B-C-D-E-D-D, or some variation of it (for example the first verse can be longer than the second one, or there can be a bridge before the last choruses after the instrumental).
This song structure allows usually the artist to get to the first chorus within the first 90 seconds mark, which is a standard in writing songs for radio airplay, and to keep the overall song lenght under 3/3.5 minutes, which is also another standard obtained by studying the average attention span of the casual listener.

Now, we know that most of the songs follow those rules to be more effective, but there are many others that prefer other structures. Some of them for example do add or subtract some element, for example by adding another part:

F) Special: a verse that is totally different from the others

Therefore another very common song structure that we could find is the following, with all its possible variants: A-B-D-A-B-D-F-E-D-D
This structure is without the bridge, therefore the song is more agile, it takes less to get to the chorus and the variation element is the special before the instrumental part, or sometimes replacing entirely it.

Let's now do a training with a couple of famous songs, let's start with a pop one: Baby one more Time by Britney spears. In this case we can clearly see a structure A-B-C-D-A-B-C-D-A-F-D-D
which is a very common pop variant of the classic structure, in which intro + special takes entirely the place of the instrumental part to make the song even more focused and vocal-centric.

Moving towards rock/metal territories, let's check out this beautiful Iron Maiden single: Flight of Icarus, one of the most famous songs of the band. In this case the structure is A-B-C-D-A-B-C-D-E-D-E, with two guitar solos alternating with the choruses in the last part of the song, since guitar solos are (unlike in pop) a trademark in heavy metal.

As you can see the most common structure can be found in many different genres, and we encourage you to listen to your favourite songs and write down the structure, then compare them among them and with yours: it's a very interesting exercise in understanding the various dynamics inside the songs, to learn what we can do to make our songs flow more effectively, and especially to learn that in this world the rules are made to be broken and completely changed!

Additional awesomeness: there are some particular bands of less commercial genres like progressive, djent or some type of extreme metal, who deliberately change the structure from song to song making them much more complex and articulated (but often less easy listening). The structures can have different type of verses rotating (es. Verse with riff 1, verse with riff 2, verse with riff 3...), or with more than one chorus alternating. Let's try to break down the incredible Make Total Destroy by Periphery: A-B1-C-D-B2-B3-B4-E-D-E-F-B5-B1 !!!

Become fan of this blog on Facebook! Share it and contact us to collaborate!!

Saturday, October 8, 2016

5 way to achieve better separation when mixing

Hello and welcome to this week's article!
Today we are going to take a look at 5 ways to achieve a better mix separation, and this article will be particularly useful to those who feel when mixing that they can't separate exactly the various instruments, letting them mask one another and creating muddiness.

This article is connected to our "the focus of our mix", "how to use equalization" and  "ear training" articles.

1) Choose carefully what to leave in the top end area: especially in crowded mixes (those with a lot of high pitched instruments like cymbals, shakers, high vocals etc), having a high end area full of eq masking and conflicts can lead very easily to a bad mix.
We don't want our mix to be confused, so we must keep it clean by using a low pass filter on almost every instrument to free up frequency space for the chosen 2 or 3 elements that we can leave to roam in this area.
This way the selected elements of the mix will be much easier to understand and in the overall sound will result less harsh.

2) Achieving separation in the low end area: similarly to the high end area, we cannot leave each element of the mix to roam free in the lower area, therefore we will have to high pass almost every track to move them further in the mix and again avoid eq masking: we should leave in this area mainly bass and kick drum, and anyway also the kick drum doesn't need to go too much low, where the bass instead could. Definitely guitars should free up some space here.

3) The most sensitive frequences to the human ear: Top end and low end are crowded, but no area of the frequency spectrum is crowded as the most sensitive one to the human ear, the one around 2000hz. This area is the one in which we should find 2 or 3 elements that will be in the front, and lower or carve the eq of the other elements of the mix. Usually the elements of the mix that must stay in front are vocals, snare and kick, but this rule can change from genre to genre.

4) Route everything in groups/busses: creating groups of tracks is good to process them together, for example routing all the vocal tracks in one buss, all the drum skins in another one, all the rhythm guitars in a third one and so on. The purpose is yes to free up computer resources, but also to give a sense of homogeneity to all the tracks inside a group processing them together, and to separate them better: it is easier to have only 5 or 6 groups to manage with eq and compression when finding the right place to every mix part, rather than 30 single tracks.

5) Don't boost too hard: if you need any boost harder than +6db you must or reconsider your starting sound, or free up place among the other instruments in that area: when you boost a sound the computer creates a digital reconstruction of what it imagines that sound would be if it was louder in that area, but the more you boost the farthest it gets from reality and it becomes twisted and unnatural.
The ideal boosts should be 2-3db if we want to obtain a pleasant, natural sound that is representative of the source sound.

Become fan of this blog on Facebook! Share it and contact us to collaborate!!

Sunday, October 2, 2016

REVIEW: Behringer V-Amp 3

Hello and welcome to this week's article!
Today we will review a guitar amp simulator, clone of the Line6 Pod: the Behringer V-amp 3.

Someone asked me: why are you reviewing so many Behringer products?
The answer is easy: it is the less expensive company for audio equipment, therefore many amateur musicians on a tight budget often are interested in these products, plus all the units I review are products that I have personally spent some time in trying, whether they were mine or they were lent to me by some friend to write the review: basically I review what I can can get my hands on for a reasonable amount of time, and this company happens to be one of the easiest to find among the people I know.

Moving to the review, this is one of the countless guitar amp / effect simulators that have flooded the market after the digital revolution created in the early 2000 by Line 6, which has changed the paradigm about digital amplifiers bringing it to the masses, and features 32 guitar amp models, 15 speaker cabinets, a wide array of effects and can be used, like the Pod (which shares even an almost identical shape and colour), as an audio interface to record and mix straight into the pc via Usb.

Tonally this unit (which is a slight evolution from the popular V-Amp 2, clone of the legendary Pod 2.0 and which was sold also as combo version with the name V-Ampire) is really, really similar to the old Pod: the simulations are not in line with the latest (and extremely expensive) guitar amp modelers as Axe Fx, Kemper, Bias or even the recent Line6 Helix, but it can still achieve sounds surprisingly usable, especially in a live environment (in studio the most trained listeners can still find the lack of harmonic richness, which was also a problem of almost all the simulator and that only the newest ones are finding a way to overcome) or for playing at home-rehearsing, therefore under this point of view the unit passes brilliantly the test the same way the old Pod would; the downside unfortunately is the same one of all Behringer products: Build quality.

This unit falls short in terms of build quality, there is not much more to add; this is where Behringer really economizes, but this in the long run is the biggest issue with all the products of this manufacturer.
I have heard countless times about pots falling off, I have even seen on my V-ampire combo that just a sligh hit of the hull on a hard corner made most of the pots fall off, and this building problem is the same for the combo version, the rack version and the desktop version, appearently also this V-amp 3 seems to suffer the same problem.

As for other products of the same company that I have already reviewed, the final judgement comes to what is the use you intend to do with this unit: do you need it for touring, rehearsing, carrying it around? Look somewhere else, these products are too easy to break (and surprisingly expensive to fix).
Do you need it just to keep it on your desk, plug and play with the computer? At a street price of 90€ more or less (c.a. 100$), this unit can still provide some good tone and versatility, so in that case you can give it a shot.

Specs taken from the website:

- 4 all-new plus 28 improved amp models multiplied by 15 speaker cabinet simulations give you a total of 480 virtual combos

- USB audio interface included, featuring stereo I/O, optical S/PDIF out, direct monitoring and separate control for phones out

- No-latency guitar-to-PC recording—edit and monitor your sound on your V-AMP 3 and record straight to your PC

- Studio quality multi-effects including reverb, chorus, flanger, phaser, rotary, auto-wah, echo, delay, compressor and various effects combinations

- 125 memory locations pre-arranged for many popular styles and embedded in the acclaimed intuitive V-AMP user interface

- Tap-tempo function and many other parameters directly accessible on the unit

- Presence control adjusts a high-frequency filter, simulating the negative feedback of tube amps

- Preamp bypass function allows use as a stereo effects processor without amp modeling

- Stereo Aux input lets you play along to a cue from your PC, CD, MP3 or drum computer for practice, teaching and home-recording applications

- Balanced stereo Line output can be configured for many recording and live applications

- Adjustable auto-chromatic tuner plus effective global configurations and equalization easily adopts the V-AMP 3 to any situation outside your home studio

- MIDI implementation includes program changes, control changes and SysEx, allowing complete MIDI remote control or automation with your preferred DAW

Become fan of this blog on Facebook! Share it and contact us to collaborate!!


Related Posts Plugin for WordPress, Blogger...